Sign In

Coffee Cup Template for Paper Cups

Type the rim, the bottom and the height of your cup, and this coffee cup template draws the exact arc the wall rolls from, so your artwork wraps the cup edge to edge with an even seam.

  • 7 ready cups, any size
  • Arc from 3 sizes
  • Seam, rim and bottom bands
  • Rolls up in 3D

Paper Cup Template

Print at 100% and check the 1 in square with a ruler before you cut.

ready cups, 8 to 16 oz, single and double wall
7
arc of the 12 oz hot cup’s wall
51°
sizes in: rim, bottom and height
3
bleed on the print shop PDF
1/8 in

How to make a coffee cup template in five steps

Five steps take you from a cup on the table to a paper cup template that rolls up around it.

Start from a template
  • 12 oz hot cup3.53 × 2.29 × 4.33 in
  • 8 oz hot cup3.13 × 1.98 × 3.66 in
  • 16 oz hot cup3.53 × 2.29 × 5.39 in
  • 8 oz double wall cup3.15 × 2.24 × 3.54 in
  • 12 oz double wall cup3.54 × 2.36 × 4.33 in
  • 16 oz double wall cup3.54 × 2.36 × 5.71 in

A coffee cup template drawn from your cup

Every cup here is worked out from the sizes you type, so the wall rolls up flat and your artwork lands where you put it.

  • Outer radius of the arc (Rₒ)12.46 in
  • Inner radius of the arc (Rᵢ)8.08 in
  • Angle of the arc51°
  • Top edge length11.09 in
  • Bottom edge length7.2 in

The wall’s arc from its centre: both radii, the angle and each edge’s length.

The exact arc from three sizes

A cup that narrows toward the bottom is part of a cone, so its wall lies flat as a ring sector. The two radii and the angle come from the rim, the bottom and the height: its top edge is exactly as long as the rim is round and its bottom edge as the bottom.

  • Rim curl0.2 in
  • Bottom fold0.31 in
  • Base

In section: the rim curl rolls out at the rim and the bottom fold turns in under the base.

Seam, rim curl and bottom fold

The seam band is the same width all the way up and hatched, so the glued overlap is even and stays free of ink. The rim curl above the top crease rolls into the rim and the bottom fold below the bottom crease turns in under the base.

12 oz hot cup11.18 × 5.79 in
Wrap for a 12 oz cup11.01 × 5.3 in

A blank for a cup machine, and a wrap for a cup you have (no rim curl or bottom fold).

A wrap for a cup you have

Set the rim curl and the bottom fold to 0 and the blank becomes a full wrap for a plain cup: print it, wrap it round and glue the seam, for a party, a wedding or a cafe sample.

Front
Back, with the seam

The wall rolled up into the 12 oz cup.

See it rolled up in 3D

The 3D view rolls the flat wall into your cup, with the rim curl turned out and the bottom fold in. Your colors, text and logo from the Design section go round with it, so you see the front, the sides and the seam.

Math
Along the side, rim to bottom (s)4.37 in
Outer radius of the arc (Rₒ)12.46 in
Inner radius of the arc (Rᵢ)8.08 in
Angle of the arc51°
Top edge length11.09 in
Bottom edge length7.2 in

Every number on the Math tab

The Math tab lists the slant, both radii, the angle and the length of each edge with its formula, and the size hint shows the flat size and the arc as you type, the figures a cup printer asks for.

Paper cup template sizes

The 7 ready cups, rim × bottom × height. Open one to change its size, its seam or its bands.

12 oz coffee cup template

The everyday hot cup, 3.53 in across the rim, 2.29 in at the bottom and 4.33 in tall.

8 oz hot cup

3.13 × 1.98 × 3.66 in, for a flat white, a cortado or a small tea.

16 oz hot cup

3.53 × 2.29 × 5.39 in, the large latte on the 12 oz cup’s rim.

8 oz double wall cup

3.15 × 2.24 × 3.54 in, the outer wall of an insulated cup.

12 oz double wall cup

3.54 × 2.36 × 4.33 in, a hot cup that needs no sleeve.

16 oz double wall cup

3.54 × 2.36 × 5.71 in, the tall insulated cup.

Wrap for a 12 oz cup

The 12 oz cup without the rim curl and bottom fold, to wrap a cup you have.

What size paper cup template do I need?

Take the cup you will print on and measure it: across the rim, outside; across the bottom edge, outside; and the height straight up from the bottom edge to the rim. Cups of the same ounces differ from maker to maker, so measure yours or take your cup maker’s figures.

The table lists each ready coffee cup template with its sizes, the angle of its arc and its flat size. For a size of your own, type it in inches or millimeters and the wall is drawn from there.

Every ready cup: rim × bottom × height, the angle of its arc and its flat blank.
SizeCupAngle of the arcFlat
12 oz hot cup3.53 × 2.29 × 4.33 in51°11.18 × 5.79 in
8 oz hot cup3.13 × 1.98 × 3.66 in56°9.92 × 5.08 in
16 oz hot cup3.53 × 2.29 × 5.39 in41.1°11.29 × 6.68 in
8 oz double wall cup3.15 × 2.24 × 3.54 in45.6°10.08 × 4.88 in
12 oz double wall cup3.54 × 2.36 × 4.33 in48.6°11.25 × 5.77 in
16 oz double wall cup3.54 × 2.36 × 5.71 in37°11.36 × 6.93 in
Wrap for a 12 oz cup3.53 × 2.29 × 4.33 in51°11.01 × 5.3 in

How the arc of a coffee cup template is worked out

A cup that is wider at the rim than at the bottom is a slice of a cone, and a cone unrolls into a ring sector. The slant is √(H² + ((D − d)/2)²) from the height H and the two diameters D and d; the outer radius is the rim’s radius times the slant over the difference of the radii, the inner radius likewise for the bottom, and the angle is 360° times that difference over the slant.

For the 12 oz cup that is 316.4 mm and 205.3 mm from the arc’s centre and 51.0° across, and its top edge is 11.09 in long, exactly round the 3.53 in rim. A straight cup, as wide at the bottom as at the rim, unrolls into a plain rectangle.

The cup is a slice of a cone; unrolled, the slice is the arc of the wall.

The parts of a paper cup template

The wall is the arc between the two creases: what shows on the finished cup. Above the top crease is the rim curl, which a cup machine rolls into the rim; below the bottom crease is the bottom fold, which turns in under the base and holds it.

Past the right end is the seam band, hatched: it goes under the left end and is glued there, the same width from the rim to the bottom. The rest is the wall your artwork covers.

Coffee cup design template: placing your artwork

Put your logo and the words people read first in the middle of the arc: that is the cup’s front, opposite the seam. Keep text and logos inside the safe area, clear of the seam band, and run the background out to the bleed line so the edges stay printed.

Lines that run straight across the flat arc curve slightly on the cup, so long lines of text read best along the arc and short words sit well in the middle. The 3D view shows the coffee cup design template rolled up, so you can turn the cup and check each side.

How to make a paper cup or a cup wrap

For a wrap, cut along the solid line, wrap it round your cup with the seam at the back and glue the hatched band under the other end; a strip of double-sided tape works too.

For a paper cup made by hand, crease the rim and bottom lines first, roll the wall into a cone, glue the seam, roll the rim curl out over a pencil and fold the bottom band in to take a round base cut from card.

The wrap rolls round and its seam band goes under the other end.

From the home printer to the print shop

The print shop PDF has a 1/8 in (3.175 mm) bleed following both arcs and both ends, a safe area, the seam band free of ink and a notes page with the radii and the angle. The home print PDF prints at actual size: the 8 oz cups print whole on one A4 page, every cup on Legal, 11 × 17 in or A3, and on Letter over two pages to tape together.

The coffee cup template also downloads as an SVG for a cutting machine, with the arcs as smooth curves and the creases as score lines, as a DXF and as a PNG. Every ready cup fits a 12 × 12 in mat.

A print shop’s file: the artwork runs 0.13 in past both arcs and both ends.

Is this coffee cup template free?

Yes. Every size, every arc and every file is a free coffee cup template, with no signup and no watermark. Save the cup in this browser, in a project file or in a free account, and come back to change it.

For a sleeve that slides on over the cup, the cup sleeve template works out a fitted sleeve from the same three sizes, and the dieline generator draws boxes and bags for the rest of your range.

Design your paper cup with AI

After a download, Design with AI opens AI paper cup design with this cup: describe the colors, the pattern and the words, and the design comes bent onto the cup’s own arc, ready to print.

You pay only for the designs you receive. For a logo, a name or a short line, the Design section adds them right on this paper cup template, and the 3D view rolls them up with the cup.

Who uses this paper cup template

Anyone who prints on cups, from one party wrap to a cafe’s first branded run.

Coffee shops and roasters

Lay out the artwork for branded hot cups on the coffee cup template, check it in 3D and send the print shop PDF with its notes to the cup printer.

Parties, weddings and events

Print full wraps for plain cups with names, dates and colors, and glue them round on the day.

Packaging designers

Take the exact arc, radii and angle for any cup size and place the client’s artwork with the seam and bleed in the right place.

Classrooms and crafters

Show how a cone unrolls into an arc, or make paper cups by hand with the rim and bottom bands.

Paper cup template FAQ

Quick answers about sizes, the arc, printing and the seam.

Open the paper cup template

Is this paper cup template free?

Yes. Every size, arc and file is free, with no signup and no watermark. Save the cup in this browser, in a project file or in a free account.

What sizes does the coffee cup template come in?

7 ready cups, rim × bottom × height: 8, 12 and 16 oz single wall hot cups, 8, 12 and 16 oz double wall cups, and a wrap for a 12 oz cup. Type any other size in inches or millimeters.

How is the arc worked out?

From the rim, the bottom and the height: the cup is a slice of a cone, and the template draws that cone unrolled. The Math tab shows the slant, both radii and the angle.

Where does the seam go?

At the back. The hatched seam band past one end is glued under the other end, so your front artwork sits in the middle of the arc.

Do I need the rim curl and the bottom fold?

For a blank a cup machine rolls, yes. For a wrap round a cup you have, set both to 0 or pick the 12 oz wrap.

Can I print a coffee cup template on Letter paper?

Yes, over two pages to tape together. The 8 oz cups print whole on one A4 page, and every cup prints whole on Legal, 11 × 17 in or A3.

What paper or board should I use?

It starts on 14 pt board, close to the 210 to 350 gsm cup stock printers use. For a wrap printed at home, 65 to 80 lb card stock wraps smoothly.

Can I cut it on a cutting machine?

Yes. The SVG keeps the arc as one closed cut line with smooth curves and the creases as score lines. Every ready cup fits a 12 × 12 in mat.

Is there a matching cup sleeve?

Yes. The cup sleeve template works out a fitted sleeve from the same rim, bottom and height, so the sleeve and the coffee cup template match.

Make your paper cup template now

Pick a cup or type your own and download the coffee cup template for your printer or your home printer.